Cisco 300-165 Valid Exam Guide

Get the best and valid Cisco CCNP Data Center 300-165 Exam Questions and Dumps that are only available at Dumsschool. Download the Free demo of 300-165 CCNP Data Center ETE Files and start preparation.

Try it Latest DumpsSchool 300-165 Exam dumps. Buy Full File here: (327 As Dumps)

Download the DumpsSchool 300-165 braindumps from Google Drive: (FREE VERSION!!!)

Question No. 1

Refer to the exhibit.

Which statement about fabric binding is true?

Answer: D

Question No. 2

Which statement about electronic programmable logic device image upgrades is true?

Answer: D

You can upgrade (or downgrade) EPLDs using CLI commands on the Nexus 7000 Series device. Follow these guidelines when you upgrade or downgrade EPLDs:

You can upgrade (or downgrade) EPLDs using CLI commands on the Nexus 7000 Series device. Follow these guidelines when you upgrade or downgrade EPLDs:

* You can execute an upgrade from the active supervisor module only. All the modules, including the active supervisor module, can be updated individually.

* You can individually update each module whether it is online or offline as follows:

— If you upgrade EPLD images on an online module, only the EPLD images with version numbers that differ from the new EPLD images are upgraded.

— If you upgrade EPLD images on an offline module, all of the EPLD images are upgraded.

* On a system that has two supervisor modules, upgrade the EPLDs for the standby supervisor and then switch the active supervisor to standby mode to upgrade its EPLDs. On a system that has only one supervisor module, you can upgrade the active supervisor, but this will disrupt its operations during the upgrade.

* If you interrupt an upgrade, you must upgrade the module that is being upgraded again.

* The upgrade process disrupts traffic on the targeted module.

* Do not insert or remove any modules while an EPLD upgrade is in progress.

Question No. 3

Refer to the exhibit.

An engineer is implementing a new network design that includes a port channel to connect an MDS core switch and an NPV switch. Which two Fibre Channel port types must be used to create the Fibre Channel port channel? (Choose two.)

Answer: A, C

Question No. 4

Which topology is not supported when using vPC?

Answer: C

The figure shows unsupported topology where a vPC is between hosts and two FEXs that are connected to one Cisco Nexus 5500 Series device. This topology does not provide a good high availability solution because the server loses the connectivity to the network when the Cisco Nexus 5000 Series device fails.

Figure: Unsupported Topology—Host vPC With One Cisco Nexus 5000 Series Device

If you need to connect a multi-homing server to a pair of FEXs when there is only one Cisco Nexus 5000 Series device, you have the option to run active or standby NIC teaming from the server.

Question No. 5


Ethernet interface 1/5 on Cisco Nexus 5548 is connected to Cisco UCS C220 rack server. What is the status of Ethernet 1/5 interface for FCoE functionality?

Answer: D

Question No. 6

Which four statements about reserved VLANs in Cisco NX-OS are true? (Choose four.)

Answer: C, E, F, G

Question No. 7

Which three items must be configured in the port profile client in Cisco UCS Manager? (Choose three.)

Answer: B, C, D

After associating an ESX host to a DVS, you can migrate existing VMs from the vSwitch to the DVS, and you can create VMs to use the DVS instead of the vSwitch. With the hardware-based VN-Link implementation, when a VM uses the DVS, all VM traffic passes through the DVS and ASIC-based switching is performed by the fabric interconnect.

In Cisco UCS Manager, DVSes are organized in the following hierarchy:


Folder (optional)


Folder (required)


At the top of the hierarchy is the vCenter, which represents a VMware vCenter instance. Each vCenter contains one or more datacenters, and optionally vCenter folders with which you can organize the datacenters. Each datacenter contains one or more required datacenter folders. Datacenter folders contain the DVSes.

Question No. 8

Which features must be enabled to implement manual MACsec?

Answer: A

Question No. 9

You configure STP on a switch that is attached to a Cisco Fabric Path domain and that has the vPC feature deployed. How do you configure STP on the switch in the Cisco FabricPath domain on VL AN 10?

Answer: C

Pseudo-Information Command

The spanning-tree pseudo-information command was originally developed for Virtual PC (vPC) and vPC+ designs in order to allow users to create a hybrid vPC and non-vPC peer switch topology. In order to accomplish this, two different BPDU priorities are sent by the switch. Though this command was created in order to work in vPC environments, it fits well in the scenario that is described in the previous section.

When you globally enable this command, there are then two different STP priorities: a lower value (or, better priority) when the switch is connected to the FP (FP core ports up/ready), and a higher value (or, worst priority) that is used in the BPDUs that are sent by the switch after it reloads.

These CLI commands are used in order to configure the FP switch to send the two BPDU priorities:

switch(config)#spanning-tree vlan x priority 8192
switch(config)#spanning-tree pseudo-information
switch(config-pseudo)#vlan x root priority 4096

Question No. 10

Which LISP component provides connectivity between LISP and non-LISP sites?

Answer: C

300-165 Dumps Google Drive: (Limited Version!!!)

Related Certification: CCNP Data Center dumps